The Blog of OBD2 TOOL

Wholesale Car Diagnostic Tools, Car Repair Software, Auto Testing Tools, Key Locksmith, Mobile Equipment,lunch x431,Autoboss V30 Auto Scanner Autoboss Scanner-obd2tool



view:  full / summary

Mercedes-Benz Oil Reset by MB Star Tools & Xentry Diagnostic Software

Posted by obd2tool 2012 on December 18, 2021 at 3:20 AM Comments comments (0)

Model: Mercedes-Benz CLA 118

Purpose: Oil Reset

What we need: MB Xentry software and SDconnect C4.

Oil Reset procedure:

Step 1. Scan

First, we select vehicle type.

Click on

Mercedes-Benz>>Passenger car>>A/B>>CLA(118)

Click on “XENTRY Diagnosis”.

Here we tick “Automatically start quick test”.

Also, when it’s connecting to the vehicle, voltage is 11.8V and ignition is on.


Then it auto scans all control units.

48 error codes we have.


Double-click it and use filter to show out controls with errors.


Step 2.Reset

We want “Instrument cluster (IC)”, so enlarge it.

Click on

Actuation>>Maintenance>>Reset general maintenance

Here we’ve got Service code, Workshop code, remaining days and distance to next maintenance.


So, click on the wrench icon “Reset general maintenance”.

See, codes change and maintenance time and days reset.


Step 3.Verify

Select “Confirmation of general maintenance”.

Click on the wrench icon “Confirmation of general maintenance” to verify.


Also, we can go to “Actual values”>>” Next service” to check again.

Then back to scan menu to “clear fault memory”.

After it’s complete, do a quick test again to verify.

Done! Nice and simple, even a DIYer can do it.

If you’re interested in the above things, you can check:

(Xentry, DAS, DTS Monaco, Vediamo)

How to configure OEM Benz C6 Xentry VCI interface

Posted by obd2tool 2012 on October 30, 2021 at 1:55 AM Comments comments (1)

How to configure OEM Benz C6 Xentry VCI Mercedes Benz diagnostic interface?




Double click “ConfigAssist” on the desktop, select XENTRY Diagnosis VCI


Click on Configure


Press Continue


Press Continue


Select Manual and enter StartKey


Save StartKey


StartKey installed successfully. Press OK to continue


Register success. Press Continue.


Click on “Couple VCI” to connect VCI


Configuration success. Quit.

Real Time Graphing using Caterpillar ET Software

Posted by obd2tool 2012 on October 30, 2021 at 1:45 AM Comments comments (0)

Real Time Graphing monitors ECM data and displays it in graphical form as it occurs. When running Real Time Graphing for the first time, a set of parameters must be selected to graph.

1). Connect Cat ET to the service tool connector, and establish communication with the ECM.
2). To run the Real Time Graphing function, select Real Time Graphing from the Information menu.


3). The Real Time Graphing screen is displayed. The Select Graph Set dialog box is displayed the first time this tool is accessed.


If the Select Graph Set dialog box displays:
1). Click the New button to create a new set. The Maintain Graph Sets dialog box is displayed.
2). Select a set from the Select Graph Set list box. As a graph set is selected, the parameters for that set display in the Parameters list box.


→Using the up and down arrows on the keyboard, each set and its parameters can be viewed consecutively in the Select Graph Set dialog box. If a set is created, it can be selected by the first letter of its name.
→A maximum of six parameters may be selected.
→Click the Save As button. The Save Graph Set dialog box is displayed, then click Yes.
→Enter the graph set name in the Enter Graph Set Name text box.


3). Click OK to accept the selected set. The selected set data is displayed in the Real Time Graphing screen.


#Screen Layout
The Real Time Graphing screen has the following areas:

ECM Title Area – The ECM title area displays the name of the selected graph set.
Error Status Text Box – The Error Status Text Box displays errors that occur while retrieving the parameter value. If more than one error occurs, the text box changes to a drop-down list for viewing all errors. “No Error Present” displays if there are no errors. “Unable to plot value” displays if the selected parameter cannot be plotted.
Legend Area – The Real Time Graphing legend area displays the selected parameters and is located above the graph. These parameters display with the corresponding line color. These colors cannot be changed. Parameters with an error will display an asterisk to indicate the parameter error is listed in the Error Status text box. The status parameter and its unit of value display on the y axis. These display on each side of the graph. These parameters display in the line color.
Graph Area – The Real Time Graphing area displays the time in seconds on the x axis (ten seconds is default) and the minimum and maximum values for each parameter on the y-axis. State parameters (for example, the only status is “On” or “Off”;), initially display with dashed lines until the graph begins to trace the state parameter’s value.
Buttons – The buttons available in the Real Time Graphing screen are:

a). Graph Sets


b). Settings


To change the graph settings:
1. Click the Settings… button. The Graph Settings dialog box is displayed.
2. Select the time, in seconds, from the X-Axis Range drop down list.
3. In the Y-Axis Range area, the status parameters are listed with their minimum and maximum default values. To limit the range, double click on the cell and enter a new value.
4. In the Options area, click the options to be displayed on the Real Time Graphing screen.
→Click Show Grid to display grid lines on the graph area.
→Click Show Symbols to display symbols on the graph lines corresponding to the symbol above the parameter.


5. Click OK to accept the changes. The graph reflects the changes that have been made. To return to the Real Time Graphing screen without making any changes, click Cancel. Click Default to return the settings to the default positions.

c). Hold/ Resume
Click Hold to freeze the graph. Because the service tool immediately stops updating the graph, this will allow parameters to be viewed at a particular instance. The Hold button changes to Resume. Click Resume to have the service tool continue updating the display.

YanHua DigiMaster 3 D3 Device not found error

Posted by obd2tool 2012 on October 7, 2021 at 2:00 AM Comments comments (0)

One of the customer reported that he got two errors when using Yanhua Digimaster 3 odometer correction tool.


When changing odometer for Audi with D3 mileage tool, he got the
“DEVICE NOT FOUND” error message, he carried on operation but to meet
another error: “Obtain BIOS information fails, please re-power” (shown
as picture below)


Possible reason:

Improper operation or improper shutdown the Digimaster 3 device which leads to the corrupt of the CPU files


Need to re-flash CPU for Digimaster3.

Download D3 Reflash SDCard rar, there is CPU re-flash instruction in the file

iProg Pro Change Mileage for Haval H6 70F3529 via OBD

Posted by obd2tool 2012 on October 7, 2021 at 1:55 AM Comments comments (0)

This instruction show you guide on how to use Iprog Pro Programmer to change mileage for Haval H6 70F3529 via obd.


Newest iProg Pro Plus iProg+ v84 v82 Free Download


Connection iProg programmer to Haval H6 by obd

Run iProg pro software,then select “Haval H6_(70F3529)”

Then click “Read EEPROM”

Input new value “123456” and click “Change KM”

Then click “Write KM Only”


Then instrument cluster will restart,then it will show you with new value.